Deutsch  English  Français

Meister Stahlbau AG     Conical supports (pylons)
     EN-1090-2, EXC 3
 
 Home
 Procedures:
  • Laser Cutting
  • Folding
  • Plate bending
  • Section bending
  • Welding
  • Edge Rounding
  •  
     Products
      
  • Cylinders, pipes, segments
  • Cones
  • Conical supports (pylons)
  • Column casings
  • Stair stringers & Hand Rails
  • Curved beams, pipes, sections
  • Art and garden design
  • Example projects
  •  Contact

     About Us

     Travel directions

     Terms & Conditions PDF
     
    At Meister Stahlbau AG, conical supports up to a sheet thickness of approximately 20 mm all round are bent from one piece of sheet metal (i.e. not from two half-shells).

    This results in the following advantages for you:

    • Less welding work
    • Less testing work
    • Less reworking
    • Less sanding work
    • Less welding distortion
      Smallest diameter
     
  • Cone height: 
  • 1,500 mm
  • External diameter:
  • 194 x 60 mm
  • Wall thickness:
  • 6 mm
  • Material:
  • S235JR

    Application: end pieces of cylindrical tubes as support for an emergency staircase.

     
     
  • Cone height: 
  • 1,685 mm
  • External diameter:
  • 212 x 120 mm
  • Wall thickness:
  • 6 mm
  • Material:
  • S235JR
     
      50 mm wall thickness

    The right-hand cone has the following dimensions:

  • Cone height: 
  • 2,570 mm
  • External diameter:
  • 951 x 773 mm
  • Wall thickness:
  • 50 mm
  • Material:
  • S355J2

    Application: second lowest section for a torpedo shaped 57m high tower in Manchester.

    Left-hand cone: for description see next picture.

     
      60mm wall thickness
     
  • Cone height: 
  • 2,500 mm
  • External diameter:
  • 773 x 600 mm
  • Wall thickness:
  • 60 mm
  • Material:
  • S355J2

    Application: lowest section for a torpedo shaped 57 m high tower in Manchester.

     
      Extreme dimensions
     
  • Cone height: 
  • 5,079 mm
  • External diameter:
  • 600 x 200 mm
  • Wall thickness:
  • 10 mm
  • Material:
  • S355J2

    Application: top of a torpedo shaped 57 m high tower in Manchester.

    This cone was also bent from one piece of sheet metal.

     
      Masts for Basel
     
  • Cone height: 
  • 4,500 mm
  • External diameter:
  • 714 x 639 mm
  • Wall thickness:
  • 30 mm
  • Material:
  • S355J2

    Application: section for a conical mast with a total height of 31 m.

     
     

    Masts for Basel

    Five of these 31 m high masts stand on Messeplatz in Basel.

    All sections were manufactured by Meister Stahlbau AG. 

     
      Conical supports for Dubai
     
  • Cone height: 
  • 4,627 mm
  • External diameter:
  • 427 x 199 mm
  • Wall thickness:
  • 12 mm
  • Material:
  • S355J2

    Location: Bur Juman Shopping Centre in Bur Dubai. 

     
      Extreme lengths without circumferential seam
     
  • Cone height: 
  • 8,500 mm
  • External diameter:
  • 400 x 300 mm
  • Wall thickness:
  • 6 mm
  • Material:
  • S235JR

    No circumferential seam and only one longitudinal seam.

     
      Supports for Audi and VW buildings

    We produce typical conical supports for Audi and VW buildings.

  • Cone height: 
  • Up to 4,000 mm
  • External diameter:
  • 400 x 200 mm
  • Wall thickness:
  • 10 mm
  • Material:
  • S235JR

    These cones can also be produced in wall thicknesses of 12,15 mm or even thicker.

      To top of page